Home > Bike Types > Mountain Bike

Crankworx Les Gets DH Tech: Brendog’s prototype Scott Gambler & inverted BOS fork

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race
2 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

Scott-VeloSolutions rider Brendan Fairclough not only had one of the coolest graphic schemes, he also had some interesting new suspension from BOS on his bike. And the bike itself is all new, taking cues from Scott’s Genius trail bike line, but obviously pulling the travel figures from their more complex Gambler. The last significant update to the Gambler was in 2015, so we wouldn’t be surprised if this was its replacement.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

The frame is far closer to the current Scott Genius, but with a few key differences, First, the main pivot sits much higher, and has a massive hollow axle.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

It also puts the BB height adjustment at the bottom of the shock, rather than the top. Fairclough’s running it in Low, and the rear axle chip is in the Long setting. Cranks are by DMR with an e*Thirteen LG1 chain guide. Note the Velcro bit stuck to the tip of the crankarm, and all along the chainstays and up the first section of seat stay.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

A zip-tie through the rear pivot keeps the shift cable held tightly to the frame…nothing to snag rocks, branches or heels.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

Head to BOS’ website and you’ll see a blank spot earmarked for this new Obsys downhill mountain bike fork…but no info yet. The inverted design has its rebound setting on the lower right leg, but everything else appears to be controlled from the top, including the negative spring.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

Preload is usually another word for “Negative”, and both seem to be set from the top. Our guess is one feeds through a piston to fill a lower chamber, but which one isn’t clear. There could also be a coil negative spring inside with the Preload offering fine tuning.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

Compression damping sits on the right leg with what we’re guessing is a bleed port off center from the tooled adjustment. Note the adjustable headset set to Steep – he’s got this bike set as long, low and slack as possible.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

It’s not just the fork that’s new. The BOS Syors rear shock doesn’t appear on their website and has a different adjustment layout than their Stoy coil shock.

brendan fairclough prototype scott gambler dh mountain bike with new BOS inverted suspension fork at crankworx les gets downhill mountain bike race

Other bits on Brendan’s bike include Deity bar and stem, Syncros seatpost and 27.5″ wheels, Schwalbe tires, and the TRP G-Spec brakes, which (along with the stem) seem to be using titanium bolts to hold everything in place.

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

2 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Matt
Matt
6 years ago

Existing Gambler front end with a new rear suspension layout? Main and upper pivot appear to be in the exact same spot…

Luiggi
Luiggi
6 years ago

The dual air setup isn’t similar to the old Rock Shox one, but to Manitou’s IRT IIRC. You’d inflate the main chamber (marked “preload” in this fork) at given pressure, and then the one controlling progressivity to double the pressure (marked “spring” here).

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.